Messages

I cut off the broken part. File the little post on the base a bit smaller and epoxy the mast back on

On rare occasions the removed data plate was found under the rear carpet on cars where the rear interior quarters and fold down were taken out for the conversion .

Imagine finding that plate!!! oh man, awesome bit of history

Stunning car, I had a sapphire blue example which went back to the states. Just a word on magnums, Treat them like fine china. I purchase and install a TON of wheels for my business. The "new" magnums rust if you look at them crooked. Go out in the rain, leave them wet, next day rust. And when they do it, it is brutal. the top coat of chrome is comically thin. Not like the old days where you just clean it off. it goes right through.

Very nice, Congrats.

Well I have now driven the car. Its an ANIMAL! its like pressing fast forward when you hit the throttle. I've had over 250 Mustangs and this one honestly scares me. The Borgeson works great. Thanks for all the replies which helped me move forward. I now have an early 390 balancer to wear on a gold chain like a Mustang Rapper.

An update for everyone

So the new 68 and later balancer and pulley went on fine.

A few nail biting days and the Borgeson is completely on and fits even with a 428 with headers.

I get the car back in a few days. Excited to try it now that the issue with the TKX install is sorted as well.

Cheers. Peter

You got that right

I went from clueless to knowing just enough to be dangerous in all this

Pulling the oil pan would have been informative but I'm already into the car so deep that I didn't want to open another can of worms

Thanks for your assist

I am looking forward to my first proper drive

Any new developments will be reported here.

A large amount of material was removed off that hatchet from all appearances

Further down the rabbit hole

Car hasn't been started since these parts were installed

You folks are the Magnum PI of Mustang Sleuths

Love it

Very legit Facebook page that helps people find cars that mean alot to them

Hello Folks,

As you kindly gave me advice I will keep you informed of my decision (right or wrong) and the outcome after install

So I went with a new 68 and later balancer and pulley.

I will have those installed and see where we are then. Of course I will report back

Thanks again

Thank you everyone

Very helpful posts

Now to make a decision and order some bits for when I come back to the states in June

Thank you. Peter

This sure looks like my current balancer

https://www.ebay.co.uk/itm/233994327623?chn=ps&_ul=GB&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&mkscid=101&itemid=233994327623&targetid=1405537545258&device=c&mktype=pla&googleloc=9045051&poi=&campaignid=17218284410&mkgroupid=142217514411&rlsatarget=pla-1405537545258&abcId=9300867&merchantid=426103394&gad_source=1&gclid=Cj0KCQjw2PSvBhDjARIsAKc2cgPm4iP5xHfNI4_Ir87kBKi0slrreOAzmU2Oia3yZQ7NFYnfoq22fvMaArJwEALw_wcB

Thank you Scott

I get what you are saying, by changing the damper then other alignment issues may present themselves. As the car has no air or power steering then my alignment issues would potentially be smaller in comparison to a fully loaded up engine belt system.

If I understand you correctly: Your feelings are that by buying the correct 428SCJ balancer which is a larger unit then what I have that there won't be, or shouldn't be any issues due to my current and the possible new SCJ correct one being neutral balance. So they won't, in theory affect the current balance of the rotating assembly.

thanks for your assistance.

Thank you Bob

I have had what you said earlier confirmed by another person about the Balancer on my car being an Early 390 unit

I spoke to the mechanic this morning and he did say the engine, although strong as an ox does have a light vibration at higher rpms. Not so much that is feels there is something massively wrong but its definitely there and definitely in the engine.

So your thoughts are that it may cause further issues if I was to source and install a correct SCJ balancer on the engine?

Thank you once again. peter