News:

SAAC Member Badges are NOW available. Make your request through https://saac.wildapricot.org  to validate membership.

Main Menu

Hot start of a 66 Shelby Mustang

Started by deathsled, November 14, 2026, 08:11:55 PM

Previous topic - Next topic

deathsled


After a stress test around the area. Car seems to be driving well and certainly cooler with the Ford option desert radiator (not available on Shelbys just for clarification. It's my option). There seems to be a vibration in the transmission tunnel at around 40 or 45 mph. I am thinking the driveshaft might be out of balance. Opinions welcome.
"Low she sits on five spoke wheels
Small block eight so live she feels
There she's parked beside the curb
Engine revving to disturb
She's the princess from his past
Red paint gold stripes damned she's fast"

trotrof1

Could be a balance issue or runout problem. Possibly a u-joint. Check to see if the transmission mount is OK. The hot restart sounds great.

6s2055

I had a simular problem on my '66 GT350. Mine was a vibration around 55-65. Tried a number of solutions including a new balanced AL driveshaft,rebalance of tires and new u joints without success. Then was using a chassis dyno to reset my webers and discovered that the third member housing was slightly tweaked upward..not much but just enough of an angle to tweak drive shaft allinement. Problem solved, even at 110 on Thunderhill straight.

Bob Gaines

Quote from: 6s2055 on November 15, 2026, 01:02:45 AMI had a simular problem on my '66 GT350. Mine was a vibration around 55-65. Tried a number of solutions including a new balanced AL driveshaft,rebalance of tires and new u joints without success. Then was using a chassis dyno to reset my webers and discovered that the third member housing was slightly tweaked upward..not much but just enough of an angle to tweak drive shaft allinement. Problem solved, even at 110 on Thunderhill straight.
I am curious when you say " tweaked upward " what were the steps you took to adjust the housing to solve the problem?
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

trotrof1

Add shims to the rear of the spring perch and upper leaf?

deathsled

I put 1 inch lowering blocks on the back myself but this was some time ago. Seems a more recent phenomenon. I will get it checked out and thank you all for the ideas to the issue.
"Low she sits on five spoke wheels
Small block eight so live she feels
There she's parked beside the curb
Engine revving to disturb
She's the princess from his past
Red paint gold stripes damned she's fast"

6s2055

Bob,the whole housing was tilted slightly upward. Not sure how they realign it. Just paid the bill and said thank you!

Bob Gaines

#7
Quote from: 6s2055 on November 16, 2026, 04:06:14 PMBob,the whole housing was tilted slightly upward. Not sure how they realign it. Just paid the bill and said thank you!
I would guess that they would have installed some kind of shim on the back side of the housing spring perch to cause the housing to tilt down . It probably didn't take much. I just wanted to confirm if that was the technique they used to solve the problem or if they found something else causing the housing to tilt slightly upward just in case others reading had a similar issue . Something like this happens typically when rear leaf springs are replaced from my experience. The same thing could happen if when lowering blocks were installed they were not installed perfectly flat or were made wrong in the case of DIY causing the housing to not sit flat and square on the leaf spring index pin causing the housing to be tilted up or down. It doesn't have to do with the lowering of 1 or 2 inches just if the block is not flat or square with the housing/perch in the case of lowering blocks.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

NC TRACKRAT

Sounds like what you are describing is called "adjusting the pinion angle" which, if improper can definitely cause vibration.
5S071, 6S1467