Topics

Looking for a FE bellhousing with late June 68 or first week of July 68 date code. Must be very nice casting with no issues. Have a perfect 8J28 housing to trade.

Don
gt350bp

Has anyone have first hand knowledge of the Drake reproduction early 428 CJ exhaust manifold? They are being advertised by NPD as exact reproductions and it appears they have the Ford engineering numbers cast in as well. Any thoughts on quality, fit and accuracy? Thinking of buying a set for a display engine.

Don
gt350bp

Shelby 10 x 2 1/2 slightly used riveted brake shoes. Been stored in the attic for 25 years +. Not sure if original or replacements. Box has CS AF169S segmented marked, but they are not segmented.

$100 oboe + freight from 32127

Don
gt350bp

Email me @ gt350bp@bellsouth.net and I'll send some photos.

Looking for a R.H. passenger side fender trim eyebrow.

Thank you.

Don
gt350bp

Looking for someone who has knowledge on the Mustang GT's used in 1994 for the Bondurant Race School. Found a possible GT that has been sitting and it will need a complete restoration. Any help or knowledge on these cars is appreciated. I have the basic knowledge of the articles and prior auction sales but would like someone who would know the details and may have an original or restored car that would be willing to share their knowledge.

Thank you.

Don
gt350bp

Nice crowds for the Brevard AACA show yesterday at the American Muscle Car Museum in Melbourne, FL. A few photos attached.

Can anyone advise on the correct fasteners to secure the interior door handles for a San Jose produced Mustang? Not an early car that would use the "Jesus" clips.

Thank you.

Don
gt350bp

Found a small box of misc. 1/25th scale model parts in the attic. Some American Racing 200S wheels and three (3) Minilites wheels are included. All parts are from
Ford related kits.

Free to a good home. First to PM me and request will get them.

Don
gt350bp 

For sale:

68 small block 4-spd. shifter for sale with new lever, mounting bolts and standard shift knob. Very nice control box. $350 + shipping from Daytona Beach area.

Don
gt350bp
(386) 756-9289

Can't find the recommended inline fuse amperage for a SW 240A fuel pump in the spec and installation sheets I have. Can anyone verify the amperage?

In addition, is there any good period correct photos of an original R-Model SW 240A installation that can be shared?

Thank you.

Don
gt350bp 

Need help identifying front coil springs. I think they came from the 69 Boss T/A replica I was building. They are 11 5/8" long.

Any help is appreciated. Thank you.

Don
gt350bp

For sale:

69 Shelby convertible diecast collection $225 Four (4) cars in photo.

69 428 CJ GT $70
68 GT 500KR $30
Yellow Ford GT $50

Shipping will be calculated on actual cost. Can pick up at the Daytona Rod Run swap meet over the Thanksgiving holiday. Will have more diecast and a large selection of Shelby and Ford plastic model kits available.

Don
gt350bp
(386) 756-9289 Daytona Beach area

Diecast models for sale:

I have the following Trans Am / GTO Series diecast models to sell as a set. These are new in the box and never displayed. Only removed from the outer boxes  twice to check when bought and to photograph. Models are as follows:

GMP #3 Ron Fellows Sunoco Camaro
GMP #11 Scott Pruet Motorcraft Mustang (Missing outer box)
GMP 7-Eleven Bruce Jenner Mustang
GMP #1 Dorsey Schroeder Whistler Mustang

$1,200 for the set + actual shipping cost

Don
gt350bp
Daytona Beach area

Looking for a part # for 28-spline yoke for a 9" center section. Needs to be 1 1/8" large cap with 4" dimension from dirt shield to u-bolt mounting face.

Thank you.

Don
gt350bp

Trying to locate a car for a friend that was last located in the Indianapolis area. Not a Shelby but I thought I would see if anyone recognized the car or knows the person the car was sold to about 35 years ago.

The car is a 66 Mustang coupe in Antique Bronze with C4 automatic, black interior and factory A/C. The car had a black vinyl roof installed that was not a factory option and had Moon hubcaps. Car was sold by my friend's dad to Bob Mathis. This is the car my friend's dad met his future wife. My friend would like to locate and see if any possibility to purchase.

I realize not much to go on, but thought I'd give it a shot.

Any help is appreciated.

Thank you.

Don
gt350bp

Can anyone advise on the stock size of the discharge nozzle on a Holley 715? I misplaced my notes and can't remember what I started with. Think it may have been a #28, as I have an extra in the parts bin. Any help will be appreciated.

Thank you.

Don
gt350bp

Looking for recommendation for best headlight switch for a 65/66. Had a flashing headlight problem last week on my trip to the American Muscle Car Museum show in Melbourne, FL. Any firsthand knowledge would be appreciated.

Thank you.

Don
gt350bp

Looking for someone with experience in Central Florida to rebuild a SW 240A electric fuel pump with gaskets suitable for 93 octane 10% ethanol pump gas.
I have the gaskets, but they did not come with any instructions. Any help will be appreciated. Would like someone local so I can watch and learn if all possible.

Don
gt350bp

Happy New Year to all!

Looking for step by step instructions for 07 to 09 GT 500 front bumper cover removal. Have not been able to locate anything specific to the 07-09 GT 500's.
Will be doing a restoration to the front clip as my car is a daily driver and did the I-4 shuffle for almost two years from Daytona to Orlando.

Any insight or information out of a shop manual will be appreciated. Do not want to take any chances of breaking any clips or hidden pieces.

Thank you.

Don
gt350bp

Lucas fog lights on Pittsburgh Craig's List for $800. Look like they need quite a bit of work and have a cracked lense, but if you need.

Don
gt350bp