We have implemented a Photo Gallery for hosting images right here on SAACFORUM. Check the How-To in News from HQ

Main Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - OldGuy

The Lounge / Re: Unread Post Distribution
June 24, 2024, 07:44:32 PM
Quote from: TA Coupe on June 24, 2024, 07:06:08 PMYou can go to your profile and click on the ignore list and put in the name of an individual you want to ignore. Eazy Peezy. Problem solved 😌 Then all this bitching and moaning can end, Capeesh everyone?


Well folks, I did implement the ignore option and I don't have to be subjected to reading the countless posts. My comment was simply that 96% of the unread posts that popped up were from one source. Having someone on the ignore list does NOT keep the posts from popping up in the Unread Posts category.

A possible reason why there is such a disproportionate ratio of junk mail verses valid/constructive mail is that those who USED to post constructive posts are leaving or holding back from posting on this forum. If I'm correct on this assumption it is truly a sad situation.
The Lounge / Unread Post Distribution
June 24, 2024, 08:34:58 AM
I just opened the Unread Posts section of the forum as I normally do early in the morning. Of the 27 posts that popped up, 26 were from Florida announcing everything that happened or is about to happen in Florida. Only ONE real post. That's 96% nonsense and 4% of what I consider legitimate.

This is just an observation on my part.

[/quote]My question is have you used them on cast aluminum like the CJ PS brackets, smog pump  housings, alt housings  or distributors? If so some "you tube" demos  talk about an ultrasonic media cleaner? I'm wondering about also using evaporust in a container submerged in the water solution to clean rusted parts?

I use my ultrasonic cleaner all the time for parts cleaning. I haven't tried it with Evaporust however. In theory I would think that the agitation/heat created by the ultrasonic cleaner would accelerate the de-rusting process however in actual use I wouldn't operate the ultrasonic cleaner for the hours/days that Evaporust usually takes to do its job. Ultrasonic cleaners generate a lot of heat that can be damaging to the crystal if left for extended periods of time.
After delving into the grey matter of what's left of my brain, I have come to the conclusion that it probably really does not matter what the size of the hole in the lifter disc might be unless it is smaller in diameter than the hole in the cupped ends of the push rod. The reason being is that the smallest hole or orifice in the lifter/pushrod/rocker arm is what is going to dictate the flow/pressure of this oiling circuit. If I remember correctly (big if) the smallest hole or orifice is the pee hole in the pushrod socket of the rocker arm that piddles oil on the rocker ball and indirectly down to the valve guide area. Please correct me if this isn not the smallest orifice. SOOOO, if all of the internal lifter pieces are similar in both of the lifters that the original OP compared, disc hole diameter size is probably a moot point.

Thanks, Royce for the good discussion and for FORCING me to think.

1966 Shelby GT350/GT350H / Re: Car stalls.
April 30, 2024, 03:31:00 PM
Quote from: paul on April 30, 2024, 02:36:15 PMWhen I got the carb back from Drew, I adjusted it to the engine and set the timing using the max vacuum as target. It is pulling about 16.5 inches now from the PCV port at the back of the intake.

I will check the lines to the transmission next. Could the vacuum lines to the transmission and/or the modulator be leaking and still allow the 16.5" of vacuum at the PCV port?

Drew does excellent work, the carb performs exceptionally.

Thanks guys, Paul

Paul, you want the pcv active when you perform the manifold vacuum test. I would suggest installing a temporary tee in the connection where the transmission vacuum line connects to the intake manifold. The pcv is, by definition, is a vacuum leak. You want to determine if there are additional vacuum leaks.

1966 Shelby GT350/GT350H / Re: Car stalls.
April 30, 2024, 01:39:43 PM
Perform a manifold vacuum test on a warm engine, idling, and in park. I don't know the altitude of where you reside, but I would expect approximately 16 inches of manifold vacuum. If it is 14 inches or less, I would expect that you might have one or more vacuum leaks that you need to hunt down, like maybe the rubber hoses that connect the vacuum line from the manifold to the vacuum modulator. If it has never been changed, the modulator could be your source also. There could be other sources of leakage but try the easiest first. It is a simple diagnostic test to perform.

I hope this helps.


Quote from: Royce Peterson on April 29, 2024, 10:51:52 AMMaking the hole smaller would increase the oil pressure.

My guess would be that it was done to decrease the oil flow to the rocker arms. I think that the smaller diameter in the discs would increase oil pressure to a very small degree.

You can question the numbers, but you CAN NOT dispute the original dirt. It would be a shame to loose that!
Quote from: shelbydoug on January 11, 2024, 01:30:31 PM
I personally think that the issue with the bolts loosening on the oil pan is caused by using a cork gasket?
Those things compress over time and that right there can cause loose bolts.

Doug is spot on! Cork compresses and rubber creeps causing the symptoms that the OP described. If one over tightens sheet metal engine oil or trans pan bolts, it distorts the pan sealing surface and causes increased oil leakage. There are non-stock band aid fixes (doublers) that can lessen the effects but once the pans are distorted leaks (seepage) will ensue.

The Lounge / Hand-built Ford Raptor in 150 Days
December 27, 2023, 01:07:52 PM
This guy gives new meaning to the Hot Rod terminology words of "woody" and "billet". Definitely worth watching.

The prices are really affordable. They'll probably sell out quickly-even for Cougar stuff.
1966 Shelby GT350/GT350H / Re: Calling Some Hertz Owners
November 15, 2023, 08:31:16 AM
803 has a MICO and override traction bars.
Quote from: tesgt350 on September 27, 2023, 11:46:20 AM
Quote from: crossboss on September 26, 2023, 08:50:40 PM
Gruesome Newsom's perfect utopia. All law abiding, tax paying citizens are fleeing Kommifornia. Let all the whack jobs, illegals, criminals, homeless drug addicts stay. Great job Governor. Another reason not to stay...

Another Reason not to even VISIT.

Just think, 'ole Gruesome is in line for POTUS! I'll bet that the line forms for 2024.
Wanted to Buy / Re: 66 GT 350 seatbelt eyebolts
September 18, 2023, 07:20:22 PM
Try Shelby Parts & Restoration for the eye bolts that you need. I bought a complete set (albeit a few years ago) of NOS eye bolts prior to Jim's passing.

Good luck.