Messages

Can anyone advise on the correct fasteners to secure the interior door handles for a San Jose produced Mustang? Not an early car that would use the "Jesus" clips.

Thank you.

Don
gt350bp

Found a small box of misc. 1/25th scale model parts in the attic. Some American Racing 200S wheels and three (3) Minilites wheels are included. All parts are from
Ford related kits.

Free to a good home. First to PM me and request will get them.

Don
gt350bp 

For sale:

68 small block 4-spd. shifter for sale with new lever, mounting bolts and standard shift knob. Very nice control box. $350 + shipping from Daytona Beach area.

Don
gt350bp
(386) 756-9289

Pretty sure the GT 350R's left the factory with a single SW 240A attached to the L.H. trunk hinge support. Only picture that somewhat shows this is in the 65 Registry. (I think that photo was originally in the May 65 Road and Track article on the 65 Shelby's.) Hoping there is a period correct photo in another magazine or maybe even a Shelby memo or sketch that would be a little more detailed.

Don
gt350bp

Can't find the recommended inline fuse amperage for a SW 240A fuel pump in the spec and installation sheets I have. Can anyone verify the amperage?

In addition, is there any good period correct photos of an original R-Model SW 240A installation that can be shared?

Thank you.

Don
gt350bp 

I am running 215/70 x 15 front and 255/60 x 15 in the rear on my KR.

Don
gt350bp

Need help identifying front coil springs. I think they came from the 69 Boss T/A replica I was building. They are 11 5/8" long.

Any help is appreciated. Thank you.

Don
gt350bp

For sale:

69 Shelby convertible diecast collection $225 Four (4) cars in photo.

69 428 CJ GT $70
68 GT 500KR $30
Yellow Ford GT $50

Shipping will be calculated on actual cost. Can pick up at the Daytona Rod Run swap meet over the Thanksgiving holiday. Will have more diecast and a large selection of Shelby and Ford plastic model kits available.

Don
gt350bp
(386) 756-9289 Daytona Beach area

Diecast models for sale:

I have the following Trans Am / GTO Series diecast models to sell as a set. These are new in the box and never displayed. Only removed from the outer boxes  twice to check when bought and to photograph. Models are as follows:

GMP #3 Ron Fellows Sunoco Camaro
GMP #11 Scott Pruet Motorcraft Mustang (Missing outer box)
GMP 7-Eleven Bruce Jenner Mustang
GMP #1 Dorsey Schroeder Whistler Mustang

$1,200 for the set + actual shipping cost

Don
gt350bp
Daytona Beach area

Roy,

Had to switch the balance on the engine to get it to set down in correctly.

The 482 was built by Keith Kraft and he suggested TD rockers, stands and shafts, so that is what I am using. The cam is a solid roller and am very happy with the results. Engine runs and sounds great with the solid lifters.   

Things have been going pretty well here in the swamp, but after 30 years in Florida, I am getting priced out. Insurances and unbridled coastal growth has me looking for cheaper property back up in Western Pennsylvania. I used to live in a town that was considered the best kept secret, but local politicians have let the growth over run the infrastructure. Traffic nightmares, flooding and new apartments and storage facilities on every available space.

Don
gt350bp

Just restored my 68 KR shifter and attached are photos of a small block and big block shifter and rods. Big block reverse shift rod is bent slightly different and has a bevel on the end for clearance. The slot in the shift rod for adjustment is slightly longer as the shifter reverse arm is bent vs. the small block is straight.

Don
gt350bp

I installed Hooker Super Comps on my 68 KR and the easiest way was as follows:

1.) Leave the engine mounts off the engine.
2.) Lower the engine to about 4-6" above final install location.
3.) Slide the headers in from the radiator opening on both sides.
4.) I used the smaller 3/8" diameter head s.s. header bolts and install gaskets and bolts finger tight. Be sure to check headers, gaskets and bolts fit before dropping the engine down in the engine bay.
5.) Install the engine mounts to the engine.
6) Tighten header bolts.
7.) Lower engine onto mounts and install bolts. If you're using a Genesis S.O. block, one mount has to be altered or the engine will set crooked.

One major complaint on the Hooker Super Comps is that the collectors interfere with the floorboard transmission mount. Headers should have been about 1'+ longer and would not have had to grind the collector for clearance.

Hope this helps.

Don
gt350bp

Looking for a part # for 28-spline yoke for a 9" center section. Needs to be 1 1/8" large cap with 4" dimension from dirt shield to u-bolt mounting face.

Thank you.

Don
gt350bp

My 68KR had the same issues and I contacted Vic at Cougars Unlimited, and he fixed me up with two flashers and new LED bulbs. Big difference but still need to have the engine running for all bulbs to flash and be bright.

Don
gt350bp

Trying to locate a car for a friend that was last located in the Indianapolis area. Not a Shelby but I thought I would see if anyone recognized the car or knows the person the car was sold to about 35 years ago.

The car is a 66 Mustang coupe in Antique Bronze with C4 automatic, black interior and factory A/C. The car had a black vinyl roof installed that was not a factory option and had Moon hubcaps. Car was sold by my friend's dad to Bob Mathis. This is the car my friend's dad met his future wife. My friend would like to locate and see if any possibility to purchase.

I realize not much to go on, but thought I'd give it a shot.

Any help is appreciated.

Thank you.

Don
gt350bp