Topics

Hi all. I am looking for a good original driver door for 67/68.

I am in Canada but I have several contacts/adresses in USA if needed.
Join together at Ford Carlisle 2025 could also be an option if shipping is an issue.

TKS
Patrick

Looking for only one "428 cobrajet' fender emblem for 69/70 New or in perfect condition. (found)

TKS
Patrick, Canada

T-Bird 67 air cleaner same as S9 500. Nice piece with surface rust. You need to take the baffle off.
400 bucks.


I will be at Carlisle Ford show next weekend. So I can bring it there for free.

Patrick

Very good 1UA crank. It is ,030 rod ,030 main and dont need to be recut. Engine has run low mileage before being disassembly.  it has been balanced to different rods weight than leman. So it would need to be rebalanced to original if you want to used leman rods.

I will be at Carlisle Ford show next weekend so I can bring it there for free.

Asking 400 bucks

Patrick

Hi... Can someone give me a pic of the rear side of the gas cap supplied in the recall on GT500 ?
I have the front not the rear.

Patrick
Canada

Hi. Anybody can explain to me why Ford put a 7.35 in Sheby's and 7.75 in Boss's ?

TKS
Patrick

Hi. According to 428 cj.org website, wintages trays was added during the 69 year production.
Anyboby has an idea what month it would have been added ?
And was it part of both cj and scj engines ?

TKS
Patrick

Hi. I was doing some maintenance on my  Gt 500 and noticed engine oil pan is very close to the cross bar underneath and left lift hook is touching the reinforcing plate of the shock tower
Is engine mounts collapsed a commun  issue ?

TKS
Patrick
 

Nice, bench tested, clean and fresh belt newly installed by professional. Harness are not cut. Bracket and buttons are include. One button has a crack as shown. Correct T8MZ
650,00 US + ride.

Patrick, Canada

Hi all. Do you know a good source to make the C9ZE B fan clutch rebuilt ?

Patrick

Complete right tube with working valve and fittings. Has Fomoco stamped on it. Last tube cylinder has had a repair as you see in last pic.
200 $ US
Patrick, Canada

Hi all. Does anyone know if canadien Shelby should have this sticker on one of the door or pole ?

TKS
Patrick

Hi. I am helping a friend want to install headers on is 67 289 tribute.
Is one tri-y headers brand exist in the market that doesnt nead to lowered the Power steering cylinder bracket ?
TKS
Patrick

How the neutral switch harness hold on his way up to the connecter? (Surely not with tyrap to the brake line.)
If my memory is not bad, there is a P clamp hold the harness at the upper bolt of switch. What kind of  clamp is it ? Like the one on valve cover ?
Is It avalible ?

TKS
Patrick

Hi, I have visited a friend's B2 1969 ground up restauration and saw the dual exhaush wire hole on the right trunk floor hand made and rough made. Anybody know something about it ?
Original body ane trunk floor.

Patrick

Air cleaner base for GT 500 Shelby 1969. May 68 too but not sure. Same for ram air mustang also. Correct buttom, height and diameter
You need to take the baffle off as second pic and add elbow for air breather. No dent. Just surface rust.
300.00 $+ the ride. I am in Canada.

Patrick

Hi, 9 inch axle from 60's with WAR A-B 4025 case without fill plug. Has fill plug behind on third member. 54 3/4 inch outside backplates. 61 inch outside shafts.
Consider it need complete rebuilt

300.00 $

PM if interested
Patrick

Hi. I need help to identify a radio a grab in a local market. Bracket and harness may help
Which year is it ?

Hi all. Any ideas how I could get back my hood part number ?
Previous  body man made a rough job and sand it out as it has been touch at front long time ago. Hood still has potential. Just a bit bowed as usuel.

Hi all. Anybody know where I could find an assembly manuel for Shelby 9. I dont know if it is the same as mustang. It could be a duplicate one.
Tks. Patrick