Topics

For sale is a pair of 1967 - 1968 NOS rocker panel moldings.

One molding is in the Ford paper/plastic while the other is in full plastic with the paper part number at the end. Both are fully sealed and include the attaching hardware

Asking $1,200 shipped to you in the US. Can provide more photos upon request. PM or email through the site.

For sale is a set of four NOS wheel well moldings.

C7ZZ-6529165-A (LR)
C7ZZ-6529164-A (RR)
C7ZZ-16038-B  (RF)
C7ZZ-16039-B  (LF)

The original Ford paper wrapping is very brittle and one molding is out of the wrapper. Glue marks are still present and will need to be cleaned off. Two out of the four bags of attaching parts will be included.

Asking $850 shipped to you in the US. Can provide more photos upon request. PM or email through the site.

For sale is an NOS C4DZ-16A238-A Radiator Support to Hood seal for 1967 - 1968 Shelbys and 1969 - 1970 Boss 429s.

Measures 38.5" which is the same as the original on my 1967 GT350. Nice and pliable and ready to install. Asking $375 shipped to you in the US. Can provide more photos upon request. PM or email through the site.

For sale is a set of three 1966 Ford Mustang/Shelby NOS wire harnesses consisting of:

C6ZZ-14290-B (Headlight harness)

C6ZZ-14289-B (Engine Gauge Feed)

C6ZZ-14305-B (8 Cylinder Alternator wiring)

Very difficult to find all three of these together at the same time. The alternator harness is still unopened in the paper bag.

Asking $1,150 shipped to you in the US. Can provide more photos upon request. PM or email through the site.

For sale is an extremely nice early Cobra on top 1966 GT350 Tachometer. This tachometer has been expertly restored by Phidon restorations and has the correct wiring, cup, dash bracket, and needle. Dated August 1965 on the back. Perfect for your 1966 Carryover car or early 1966 GT350. SOLD.

I'm looking for a 1967 High Performance manual.

I have a 1965 or 1966 NOS version for possible trade or will purchase outright. Shoot me a message if you have a '67 version.

For sale is a set of four Goodyear Speedway small letter tires (CC7EX). Still wrapped in the shipping tape. I have two sets of these and decided to only use one. Took a year and a half to get and now back ordered again. These are $500-550/tire depending on retailer. Sold.

I know the 68 GT350s used a C8ZE distributor with vacuum advance but was wondering if a C5OF dual point distributor could be made to work with an automatic 68 350?

For sale is an original 55 amp alternator with 13 blade fan and large pulley from a 1966 K code. This was from my 1966 K code fastback built February 1966. I sold the car and no longer need it. Sold.

For sale is a set of 1965 hipo 289 motors mounts, complete minus one intermediate mount. Need to be cleaned up but a nice start for someone wanting originals on their car. $550 plus the ride. PM or email at brittonwhitworth at hotmail.com

For sale is a C5OE hipo 289 balancer with a date code of J5.

There is some putting on the outside surface (could be filled in if desired).

Asking $325 plus the ride.

PM or email direct at brittonwhitworth@hotmail.com

For sale is a complete set of 5 front windshield moldings for all 1965 - 1968 mustang coupe/fastbacks.

Part numbers are:

C5ZZ-6503148-B
C5ZZ-6503137-B
C5ZZ-6503136-B
C5ZZ-6503144-B
C5ZZ-6503145-B

Sold

For sale is an NOS high performance 289 camshaft. Ford part number C3OZ-6250-C, still in the original tube. I tried to show a photo of the faint Ford marking stamped into it. Sold.

For sale is a pair of black 1967-1968 kick panels for a coupe or fastback. I ended up with two pairs of these, so I'm selling one.

Ford part numbers on the boxes are C7ZZ-6502344A1A and C7ZZ-652345A1A. Back of the panels are stamped with C8ZB and C8WB engineering numbers. Sold.

For sale is an original C5OE harmonic balancer dated B7 (February 1967) for a 1967 GT350. It looks like the seal has been replaced previously.

Looking for an original 1967 mustang 4 speed shift knob and an original (uncracked) driver side kick panel for coupe/fastback. Please shoot me a message if you have these parts or may know of someone who does. Thanks.

I am excited to share with everyone that I am the new owner of 1967 GT350 #2645.  I recently sold my 1966 K code fastback and it has been my dream since I was 15 to be a Shelby owner, so I started the search for one.  I was initially looking for a 1966 GT350 (since I've always had 65/66 mustangs) but through some kismet I came across 1967 #2645 via word of mouth from my father.

2645 is a moss green, 4 speed, with magstars and thermactor.  The car is unrestored and still wears its original paint, interior, and drivetrain. All the correct hard to find parts are there. Even the original Goodyear Speedway spare tire is still in the trunk along with the original trunk mat, etc. Most interestingly, the original Ford door tag was found under the carpet.

It has a documented ownership history and is a life long CA car with the original black plates from 1967 still on it.  Each prior owner took care to keep the car original and true to what a 1967 Shelby is. 

It should be arriving next week and my plan is to clean and detail the car up and replace the minor incorrect items such as coil and starter solenoid with originals and then drive it. My 3 year old daughter is already looking forward to rides in the new "mustang."

Looking forward to being a part of the Shelby community and expanding my knowledge of 67s.

Without further ado, here are some photos of it.

I am trying to confirm the correct coil mounting location for a GT350 thermactor (non-AC car).  I've seen it in several locations and think that either on the passenger side head (if there is enough space?) or intake is correct. Thanks.

For sale is an original 1966 Shelby "Over the Counter" wood steering wheel manufactured by EFFPI in Italy.

There were several iterations of this wheel, this version is the 2nd generation/middle version with welded on cancel pins on the back and black boots at the end of the spokes (see last pic for the different versions). This style wheel would have been available in 1966 to purchase as opposed to the later 1968 and on style. The wheel was professionally restored by Jeff Stephens last year and has not been installed since the restoration.  This is an extremely nice steering wheel. SOLD.

Also, for anyone who is curious, the photo comparison of the three wheel types was put together by Cory (6S1640).

For sale is an original 1965-1966 Mustang K code/Shelby original carburetor choke cable. Bracket has been repainted and knob is in good shape. Original sheathing does have a couple cracks in it. I believe Jack at DeadnutsOn can supply a correct style replacement sheathing, if desired

Sold.

Shoot me a message, if you are interested.