Topics

Hello,

1968 Shoulder harness, y belts with 1968 dated retractors for sale.
Asking $ 2850.00 for both retractors that bolt to rollbar in Fastback, and the genuine shoulder harnesses.

Thank you in advance.

Hello,

Can any wire expert confirm Tach dash version from this tag?  ED-C8ZB-14401-AV.  IF CORRECT, WHO IS A RECOMMENDED HARNESS REFURBISHER/?

Thank you

Hello, what is the best or better asked, safest product to clean the textured cover, this needs more than just water on a cotton towel.  Looking to add this to my 1968 convertible project.

Thank you for any assistance.

Hello, anyone have a pair of rear retractors for ROLLBAR over the shoulder harness for 1968 convertible thanks in advance for assistance.

Hello,
I bought a 1967 Scott Drake Tach dash under dash harness.  What is the difference with a 1968 car?  Can it be used in a 1968 early car, to add the option?  My dash assembly is 1968.  Trying to add tach.

Any assistance?  Anyone know the differences that matter?  Wiper?

Thank you

1968 Fastback Fender Extension (driver side) (end cap) NOS, never mounted on car. $ 600.00 plus shipping.  I have a good used passenger side as well.

In Delaware.

Thank you

Hello,
What is the best way to restore the black camera case and Crome dash housing?  Is there a Crome paint that anyone has had good success with?  Or replacement is the only way to go?
See pictures...
Thanks for any recommendations.

1968 Drivers side lower scoop.  Genuine fiberglass is harder and harder to source. Selling off pieces to pay for the parts I need for my 500 Fastback.  Asking $425, plus shipping.  In Delaware.  Pick it up, if close. Thank you.

Hello, can anyone tell me what this is?

Came in trunk of 1968 Mustang convertible I bought recently with a SN-92 Paxton head and had an older c5 or c6 numbered 4 barrel carburetor.  I don't have any other parts, I Dont think.  Car is a C code in the VIN.



ANY ASSISTANCE?  Thank you in advance.

Parts will be for sale, funding the convertible project needs, as I go.

Started a new project 1968 convertible clone Shelby/California Special...need the passenger side similar to the photos shown...any one have some 1990's Cobra Glass needing a new home?  I understand this is best fitting parts, except for genuine Ford.  Any help?  Thank you in advance.

Tilt column removed and well stored for years. Joint feels tight.  Appears complete with covers.
Asking 1100.00. Plus shipping

Thank you

Hello,

Anyone have August 1994 Mustang Monthly for sale?

Thanks for any assistance.

Hello,

Pair of genuine 15 x 7 Shelby K-H Magstar Wheels.  See picture for Kelsey stamp and date code.

Asking  $ 900.00 for the pair, plus the shipping expense, depending on destination.  Pick up ok too...if close by.

Thank you, P M if you have questions.

Any ideas for next year?

November 26, 1967 built car needs a good rust free (hoping) drivers fender.  Car in Alabama, what is out there for sale, sunlit gold original color.

Anyone have a good used for sale?

Thank you.

Set of 4 of each wheel, 1967 Magstar or 10 Spoke version.  See pictures below.
$ 800 a set.  Can deliver to SAAC 49.
These are new and never mounted.

Thank you

1967 Shelby rear seat belts.  In Ford boxes.  $ 1200.00. Can bring to SAAC 49.

Thank you

Genuine 15 inch Kelsey Hayes Magstars for sale.  I have 9 wheels for sale.  Can bring to SAAC 49.  $ 500.00 each

Thank you

Correct, 1967 Shelby under dash gauges. POD needs refinish, extra black camera case surround, new old stock, for right side of pod.  Correct gauges.  $ 1500.00

Can bring to SAAC 49.

Thank you

Factory roll bar with retractors for sale.  Cover's included, this has the "feet" to weld to the floor.
Can bring to SAAC 49. 1967 version, with the retractors with black caps.

$ 7500.00, thank you.