Topics

Hey All,
Cleaning out some shelves. I have 2 9" housings and gears for sale

Housing date 7A6 (Jan 67) pinion support 6M20 $100
Housing date 7J1 (Sept 67) no pinion support $75
3.50 gears $100
3.00 gears $50


Thanks for looking

Hi All,
69-70 GT350 hood seal, Never installed. N.O.S. from (I think) Branda.
$150 plus the ride.

Hey All,
Drew just restored my 3259, but I found another date closer to my car, so it is for sale.
$3850.

https://www.facebook.com/AirFuelSParkTech/posts/pfbid02ps3fJVTtfFSiQRuZyiDXdCuJRhYaDycViXRkM8vqeqrpY8PYLZ4f8bnnDAHfcgXul

Hey all,
Looking to build a roller stroker motor and store my original engine for safe keeping. I want to try to keep the "clack clack clack" of my Hipo as the mechanicalcam is part of the "soul" of the gt350. Looking for recommendations of off the shelf or custom grind. If custom, can you share the specs? Looking for smooth idle and good drivability like the original. Thanks in advance.

Hey All,
I have a set of 69 gt350 plug wires from Marti Auto Works.Dated 4Q 68. New in bag. $40 plus the ride.

Tom

Why is it when I attach photos, only the link appears. How can I get it to display the photos?

Hey all
I have a 31 spline trac lock spindle to trade for 28 spline. I'm in So Cal.

Tom

Hey All,
Thinking of selling my set of 5 repro 14 x 6 chrome magnums with lugs and Shelby caps. Dated 2012. What are they worth? Also a full set of Blue Streak tires, good tread, but they are old, so I would use them for show only

Thanks,
Tom

Hi All,
Trying to help out a friend. He is an older gentleman who has had this rev limiter on his pegboard for a long time and he would like to sell it, so I'd like to get him a valuation. It appears to be in very nice nice physical condition but the harness is cut. Let me know your thoughts.
Thanks,
Tom

Hi All,
I had picked this up with some other stuff so I don't know much about it. It appears to be a Branda 1/4 window set. It is missing a few pieces, (the small window trim pieces and 1 window gasket). I dont think it's ever been installed. Asking $300 plus the ride. Not sure of the price, but If I'm way off let me know.

Thanks,
Tom

Hi All,
Recently picked up a few carbs. All are untested. All plus shipping.

3255-BE Date code 4B2
Was told these were race prepped from Ford/Holley, mechanical secondaries, no choke
427 Cobra?/ GT40? $1000

3259 reissue, Date code 1192 $1000

8007 looks barely used $250

Thanks for looking,
Tom

Hey all,
Trying to replace the sending unit for my temp gauge. I read the SW 2328 motor craft unit (with the green top)was correct, however, the threaded lug that the wire connects to is smaller than the connector. What it the correct sender?

Thanks,
Tom

How can I ID a correct air cleaner and snorkel? Need to find correct one. Is there any interchangeablity? Same for the heat tube.
Thanks

Did the 4 speed cars have a NSS? I'm able to start the car with the steering wheel in the tilt away position.Just curious
Thanks,
Tom

Hey All,
I have a repro oil pressure gauge. Can someone chime in on which wires go to which terminals. I've numbered them 1, 2, and 3.
Thanks so much.
Tom

Hey all,
Looking for a set of '69 console gauges for my early '69 GT350.
Lemme know what you got.

Thank,
Tom

Hey All,
Recently purchased a 69 GT350. The tail lights were not working but the PO had purchased a repro sequencer. Plugged it in and driver side works but passenger side does not. Checking the wiring with a test light before the box and the White/Blue wire gets power and flashes, but how does the White/Blue wire get power to the Orange/Blue, is the wiring wrong? Or possibly the new sequencer?

Thanks,
Tom

I have a S7MS-9424-A intake manifold. very nice condition. $500 plus the ride.

Hey All,
Looking to rebuild my master cylinder. When I look online, the kits available say "All except GT350". I'm not sure why the notation, other than maybe they are referring to a MICO master? Seems to me any kit for disc brakes would work, right? If not, can someone refer me to the correct kit.

Thanks,
Tom

Hey All,
I just want to give a shout out to Rraceme (Fred).
I met Fred through this forum. We have a camaraderie in that our two cars #2227 & 2228 are sequential numbers from both Shelby AND the San Jose factory. Both Sapphire Blue.
About a month ago, someone pointed out to me that I was missing the bracket for the torsion spring on the trunk lid. I asked Fred if he happened to have one.
Not only did Fred locate one, he blasted it, painted it Sapphire Blue, and send it to me. I offered to pay him, but he wouldn't accept a dime.

Since buying my car in 2021, I've found that the Shelby community is the best group of motorheads I've ever met.

It's people like Fred that is what makes this group so great.

Tom