Topics

In need of an original or nos front passenger side disc brake hose for my 70 Shelby, would prefer date to be prior to February 69, thx Keith

wanted original drivers side exhaust pipe(intermediate) for a 69-70,gt350, need an original, prefer nos but nice used ok, this is same as on a 69 mustang with 351w 4bbl. car..thx keith 318-393-1502...this pipe is different from 68 as it has the flat spots in 69.

wanted...69 -70gt350 ,original chrome autolite oil breather cap, this is the push on one..thx keith 318-393-1502

Wanted .. original air cleaner stud for 69 mustang / Shelby(gt350) with 351w  4bbl. Carburetor (autolite 4300).Stud will be 1/4-20 on each end and approximately 4 1/4 in overall length...top part length,where air cleaner wing nut goes is approximately 1 7/16 -1 1/2 above separation nut. Thank you Keith 318-393-1502

Looking  for two 16in anco wiper blade inserts,will have 2782444 on the rubber in very small print. Either nos or very nice used. Thx Keith 318-393-1502

would like to know the proper choke heat shield on 69-70 gt350. information so far is the part is listed in the 69-70 parts list as c9zz-9861-B , dont know what that looks like...would love to see an nos one.  know the c9zz-9861-A version is for the 2bbl. version 69 mustangs. have a choke heat shield from a 69 mustang with the 351w 4bbl. carburetor....this will not fit due to the carburetor height reduction on a shelby ,when a different carb spacer is used than a 69 351w 4bbl. mustang. this part is shown on coralsnakes website but has been cut to fit. dont know if ford or shelby modified the production part or was the flat shield version used as seen on some 69-70 gt350 cars. if someone has an original survivor car ,would love pictures. would also like to know what part number in parts book shows for production 69 mustang with 351w 4bbl. engine...any help is appreciated, as goal is to find out what really came on a 69-70 shelby gt350 for a choke heat shield. thx keith

Does anyone sell replacement parts for the c7 and c9 round Dearborn 1969-70 starter solenoid...internal pieces...thx keith

Wanted 1969/70  4 speed shift knob retaining nut used original or nos thx keith

wanted original 69-70 shelby front license plate bracket,thx keith 318-393-1502

what is the length of 69-70 gt350 air cleaner stud.... did shelby or ford  change out the stud for the taller fa-50 element, because the factory stud is too short(regular 351w used a fa-41 and a completely sealing air cleaner lid)...thx keith

wanted original diamond,LH, wheel weights...need assorted sizes   .25,.5,.75,1etc.... thx keith 318-393-1502

Wanted original distributor lead with orange boot for 70 351w  distributor...single lead orange boot...thx keith 318-393-1502

what do the experts say on shelby wheel weights....diamond(LH),micro ,etc ...and on front and back of wheels....remember theses wheels were installed at A O SMITH not ford...eager to hear...thx keith

1970 gt350 ...what is the correct color on the distributor lead boot(goes to coil)...remember this distributor was changed during 70 year conversion and stamped ED and had a dual vacuum advance...thx keith

wanted nos or really nice working used 1969 heater valve ,need c9 number part,which has the brass body vs plastic ,thx keith 318-393-1502

wanted 6  used original tower clamps...1 1/16 size...dated 4/68 or 1/69 ..used on heater hoses...thx keith

need help...does anyone know the part number for the thin blackish carburetor base gasket(2 used,one above and 1 below spacer), on the 69(70) gt350 ?   thanks keith...ps i have one that came with my nos spacer, but i dont know the part number...thx again

Could someone please confirm the correct pcv valve for the 70 gt350.... thank you

WANTED NOS FAN BELTS FOR A 70 SHELBY GT350...AC AND ALTERNATOR BELTS....C4TE-8620-AC1,3 OR 4 AND C4ZE-8620-B2...PREFER 1ST QUARTER 69 BUT 4TH QUARTER 68 ALSO WORKS...THX KEITH 318-393-1502

i am in need of an original c8oa-B front strut bar bushing.... good used , really just need one front bushing ,but will buy whatever. also i do have several sets of  nos c6 (front and rear) bushings,two extra c8 rear nos, as well as DO(fronts) ones if someone needs a trade. the bushings are for a 70 shelby gt350 vert. thx keith 318-393-1502