Messages

Still searching. 
Set purchased on eBay was not accurately discribed. Unfortunately the structural wire frame was separated from the rubber. Unusable.

So my search continues.
I will also buy a complete NOS L/R vent window seal set. 
Thank you. 

Fran

Searching for an NOS passenger side vent window gasket .
Ford Part Number: C7ZZ-6521448-A

I do have a drivers side (left) that I would trade. C7ZZ-6521449-A

I will buy a complete set if you don't want to split them.



Thank you
Fran

Sourced.  Thank you for the leads. Greatly appreciated.

These photos were taken and produced by D. Chadwick, West Virginia.
Photos were part of the photos taken at SAAC Conventions.
 
These Photos were displayed and do have small tack marks,some very small corner rip where the tack was(in the border only) , some discoloration from being displayed.
Certainly I can send you more photos, if you have specific questions.

SAAC7
Measures 53x10 inches
This was Great Gorge NJ
1982
$100

SAAC9
Measures 61x10 inches
This was Anaheim Ca
1984
$100

SAAC Charlotte
Measures 52x10 inches
Cobra Track Photo with Carroll Shelby
$125

SAAC 10
Measures 61x10 inches
$100

SAAC 14
Measures 52x10 inches
$100

Ford GT40 Reunion
Measures 57x10 inches
Watkinsglen 1989
$150

Possible delivery to SAAC convention.

Thank you
Fran

Wanted:
NOS Top Loader Cover
Ford Part Number: C4AZ 7222 A

Must be no pits.
I might be interested in a very good used OEM.

Thank you

Fran

Sourced an NOS cover, no longer looking. 

Thank you. 

Ford Part Number C7ZZ 6503150 A.
This is the black plastic type part that clips in the lower stainless trim.

Not used for 1965, 1966 Mustang. Different part was used after 1968.

Used on 1967 and 1968 Mustang and Cougar.

I need at least 2.


Thank you.
Fran

Shipping cost is additional $
All items are NOS, unless noted differently

C9ZZ 6687 B  Oil Pan Windage Tray
Ford 1969-1970 Boss 302 + 289 HiPo $175
No hardware included.

C3DZ 8149 B 289 HiPo Fan Shroud Brackets. Set of 4.  SOLD
Ford 1965-1966 Mustang + GT350

C5AF 10A352 H Alternator Pulley. Have 2, $225 each.
Ford 289 HiPo

S1MS 9431 C Exhaust Header Flange Kit $325
Ford 1965-1966 GT350. Complete

S1MS  3590 A Steering Pitman Arm $425
Ford 1965-1966 GT -350

C8AZ 1190 A Front Inner Wheel Seals. Have 3, $10 ea.
Ford 1965-1967 Mustang + 1965-1967 GT-350

S1MS 5260 A3A Header Flange Gasket, Have 2 $65 each
Ford 1965-1966 GT-350

S1MS 16229 A Rear ID Plate "GT-350". $175
Ford 1965-1966. * some damage.

C5ZZ 11654 A Head Light Switch $125
Autolite Before 8/17/64 1965 Mustang + GT-350

C5ZZ 13220 C Right Side Parking Light Retainer $70
Pkg of 1 Ford 1965-1966 Mustang + GT-350

C5ZZ 13221 C Left Side Parking Light Retainer $70 each
Pkg of 2 Ford 1965-1966 Mustang + GT-350

C5ZZ 13221 C Left Side Parking Light Retainer $70
Ford 1965-1966 Mustang + 1965-1966 GT-350

C5ZZ 2457 B Clutch Pedal Pad $35
From 3/8/1965 1965-1967 GT-350

C5ZZ 6522053 B Mustang Ignition Key Blanks, have 10, $23 each
Ford 1965-1966 Mustang + GT-350

BF-42 Spark Plugs (Box of 10) $70
Motorcraft

C1AZ 6731 A FL1 Oil Filters, have 23 qty . $35 each
Motorcraft


Thank you.
Fran

Wanted: Looking for very nice original pulley, GT500KR application

Stamping should read :

C8AE 9C480A   FRONT
Fomoco

See attached photos for details of what I'm searching for. 
I'm trying to upgrade my pulley.

Thank you

Located.   Thank you for the assistance.

Fran

Looking for what has worked best for removal of the plug wire bracket on aluminum valve covers.

Carefully.. Slot the head, or weld to the U drive head... then unscrew? (similar to process used to remove the transmission serial tag).  ??

How to recreate the surface treatment on the unpainted areas? After proper paint (unpainted areas are carefully taped during paint)

Lightly sand (grit?) in a forward and back direction to create a "brushed aluminum" finish.

Comments appreciate.
Thank you.
Fran

Basically 75-90% of the cars chrome.
Bumpers, door handles, front side marker lights, backup lights, gas cap, headlight trim surrounds, tail light bezel surrounds, vent window uprights, sail panels..

Cores are very good, other than the typical sail panel pot metal pitting.

Searching for recommendations, based on your recent experience.
Plating of pot metal to steel parts.
Prefer shops located in the NE US, that have a reputation for quality chrome plating.
This includes all proper material preparation for show quality chrome.

Any suggestions are appreciated.
Thank you

Fran

Updated:
Show quality chrome requires much attention to detail to prepare the part, and typically uses a triple plating process of copper, nickel, chrome. Many plating shops are not interested processing pot metal.
Not all chrome shops apply this process and material plating thickness.
The recommendation of Paul's Chrome is typical of the process required to create 'show chrome'

Has anyone been there recently?

Thks
Fran

Wanted

1967,1968 Weatherstrip, Right Door

NOS weatherstrip:
Passenger Side Door, part number C7ZZ 6520530-A

Thank you
Fran

Wanted: NOS Mustang Heater Box Fan Motor. Non AC application. 2 Wire
Stamped: 12v, Autolite
Ford PN: C5ZZ- 18527
Engineering PN: C5ZF-18527-A

Any assistance is appreciated.
Thank you
Fran

PM sent


Example photo from SAAC Forum member.. ( Thks Don)

Wanted:
1968 NJ Hood Latch
Looking for production line hood latch
Correct stamping double "A" or "W" .
The most obvious place to find that stamping mark is on the outer facing safety catch. "J" shaped metal area.

Thank you.
Fran

Sourced with SAAC Forum members assistance!
Thank you.