SAAC Forum

The Cars => 1966 Shelby GT350/GT350H => Topic started by: deathsled on November 14, 2026, 08:11:55 PM

Title: Hot start of a 66 Shelby Mustang
Post by: deathsled on November 14, 2026, 08:11:55 PM

After a stress test around the area. Car seems to be driving well and certainly cooler with the Ford option desert radiator (not available on Shelbys just for clarification. It's my option). There seems to be a vibration in the transmission tunnel at around 40 or 45 mph. I am thinking the driveshaft might be out of balance. Opinions welcome.
Title: Re: Hot start of a 66 Shelby Mustang
Post by: trotrof1 on November 14, 2026, 08:32:38 PM
Could be a balance issue or runout problem. Possibly a u-joint. Check to see if the transmission mount is OK. The hot restart sounds great.
Title: Re: Hot start of a 66 Shelby Mustang
Post by: 6s2055 on November 15, 2026, 01:02:45 AM
I had a simular problem on my '66 GT350. Mine was a vibration around 55-65. Tried a number of solutions including a new balanced AL driveshaft,rebalance of tires and new u joints without success. Then was using a chassis dyno to reset my webers and discovered that the third member housing was slightly tweaked upward..not much but just enough of an angle to tweak drive shaft allinement. Problem solved, even at 110 on Thunderhill straight.
Title: Re: Hot start of a 66 Shelby Mustang
Post by: Bob Gaines on November 15, 2026, 09:37:52 AM
Quote from: 6s2055 on November 15, 2026, 01:02:45 AMI had a simular problem on my '66 GT350. Mine was a vibration around 55-65. Tried a number of solutions including a new balanced AL driveshaft,rebalance of tires and new u joints without success. Then was using a chassis dyno to reset my webers and discovered that the third member housing was slightly tweaked upward..not much but just enough of an angle to tweak drive shaft allinement. Problem solved, even at 110 on Thunderhill straight.
I am curious when you say " tweaked upward " what were the steps you took to adjust the housing to solve the problem?
Title: Re: Hot start of a 66 Shelby Mustang
Post by: trotrof1 on November 15, 2026, 10:03:15 AM
Add shims to the rear of the spring perch and upper leaf?
Title: Re: Hot start of a 66 Shelby Mustang
Post by: deathsled on November 15, 2026, 11:31:47 AM
I put 1 inch lowering blocks on the back myself but this was some time ago. Seems a more recent phenomenon. I will get it checked out and thank you all for the ideas to the issue.
Title: Re: Hot start of a 66 Shelby Mustang
Post by: 6s2055 on November 16, 2026, 04:06:14 PM
Bob,the whole housing was tilted slightly upward. Not sure how they realign it. Just paid the bill and said thank you!
Title: Re: Hot start of a 66 Shelby Mustang
Post by: Bob Gaines on November 16, 2026, 04:41:30 PM
Quote from: 6s2055 on November 16, 2026, 04:06:14 PMBob,the whole housing was tilted slightly upward. Not sure how they realign it. Just paid the bill and said thank you!
I would guess that they would have installed some kind of shim on the back side of the housing spring perch to cause the housing to tilt down . It probably didn't take much. I just wanted to confirm if that was the technique they used to solve the problem or if they found something else causing the housing to tilt slightly upward just in case others reading had a similar issue . Something like this happens typically when rear leaf springs are replaced from my experience. The same thing could happen if when lowering blocks were installed they were not installed perfectly flat or were made wrong in the case of DIY causing the housing to not sit flat and square on the leaf spring index pin causing the housing to be tilted up or down. It doesn't have to do with the lowering of 1 or 2 inches just if the block is not flat or square with the housing/perch in the case of lowering blocks.
Title: Re: Hot start of a 66 Shelby Mustang
Post by: NC TRACKRAT on November 17, 2026, 09:19:53 AM
Sounds like what you are describing is called "adjusting the pinion angle" which, if improper can definitely cause vibration.