News:

SAAC Member Badges are NOW available. Make your request through saac.memberlodge.com to validate membership.

Main Menu

428 Cobra Jet heat shield pan under intake

Started by Bob Gaines, May 09, 2024, 08:58:19 PM

Previous topic - Next topic

Bob Gaines

I am trying to get a take on how important the metal pan is under the CJ cast iron intake.I have a chance to buy a cast iron CJ intake at a reasonable price unfortunately it is missing the sheet metal heat shield pan. I understand the pan is Cobra jet intake unique so I can't substitute one from a 390.What say you?
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

pbf777

    As you obviously realize, without the shield, well, it's just not going to be "correct"; but of coarse once installed who would know?  ::) 
    The actual purpose of this shield is to reduce the sum of splashed oil that might come in contact with the exhaust heat cross-over passage section of the casting located on the bottom; this intended to reduce the sum of that oil which might be "damaged" by the excessive heat exposure and even worse will tend to "coke", even becoming a solid contaminant suspended in the oil.  ;) 

    So, if ones' vehicle is just driven off trailer to the display parking spot, or just never allowed to get hot (for fear of burning the engine or manifold paint  :-[ ), or even just never run hard producing elevated exhaust temperatures, or best, the intake manifolds' cross-over passage is blocked (reduces the burnt paint on the top of the intake issue, or is done to reduce the tendency for fueling vapor-lock  8)) it probably really isn't a necessary component (that is as long as you don't tell anyone its' missing!  ::) ).

    Scott.

Bob Gaines

I suppose I will just fabricate a makeshift shield or block off the cross over. Thanks.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby


Bob Gaines

#4
Quote from: Coralsnake on May 10, 2024, 05:55:01 PMClose but no cigar

https://www.ebay.com/itm/NOS-1966-1967-1968-1969-FORD-FAIRLANE-GALAXIE-MUSTANG-390-428-INTAKE-BAFFLE-PLAT-/392769646463
I can do a awful lot of fabricating before spending money on something like that which would have to be modified anyway to work given the CJ one is shaped different. I have decided to go the block off of the heat riser route given the car will not be cold weather driven but thank you for thinking of me. 
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

Royce Peterson

We used to stuff the intake crossovers with crumpled up aluminum foil when I was young and poor. It worked pretty well.
1968 Cougar XR-7 GT-E 427 Side Oiler C6 3.50 Detroit Locker
1968 1/2 Cougar XR-7 428CJ Ram Air C6 3.91 Traction Lock

Bob Gaines

Quote from: Royce Peterson on May 10, 2024, 07:32:26 PMWe used to stuff the intake crossovers with crumpled up aluminum foil when I was young and poor. It worked pretty well.
I could see how that could work for awhile but would be concerned about burn through at some point . Come on Royce I am waiting for you to give me a better alternative then that. ;D 
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

J_Speegle

They make cross over block off plates for SBs never seen  or at least recall seeing them for sale for BB of any kind. Might be a small market for someone that wanted to get crafty at home in the garage,  With a couple of patterns I would start with a chunk of hard wood, trace the pattern and relief out with a bur head or drimmel tool then shape some plates and hammer them for a depression to hold them in place. SB ones are fairly thin metal so that they don't get in the way of the posts sealing (too thick of sheet metal)

Just a thought about a possibility
Jeff Speegle- Mustang & Shelby detail collector, ConcoursMustang.com mentor :) and Judge

Bob Gaines

Quote from: J_Speegle on May 10, 2024, 10:05:12 PMThey make cross over block off plates for SBs never seen  or at least recall seeing them for sale for BB of any kind. Might be a small market for someone that wanted to get crafty at home in the garage,  With a couple of patterns I would start with a chunk of hard wood, trace the pattern and relief out with a bur head or drimmel tool then shape some plates and hammer them for a depression to hold them in place. SB ones are fairly thin metal so that they don't get in the way of the posts sealing (too thick of sheet metal)

Just a thought about a possibility
Thanks for the input. I am leaning towards a .030 piece of stainless in the gasket cut out for the heat riser port just enough oversize to keep from falling in and silicone the plate in with the gasket . At least until I hear a better procedure.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

vtgt500

In the late '70s while working at Ford T&C I spent my free time hanging out at a couple of the more successful engine builders in Livonia.  Was told the benefit of using the turkey pan was to keep the intake charge cool as possible.

Bob Gaines

Quote from: vtgt500 on May 11, 2024, 04:26:18 PMIn the late '70s while working at Ford T&C I spent my free time hanging out at a couple of the more successful engine builders in Livonia.  Was told the benefit of using the turkey pan was to keep the intake charge cool as possible.
I think you are mixing up two different pan terms. The Turkey pan is normally used to describe a enclosure around the carb which resembles a thanksgiving turkey pan. It is seen mostly used on competition Cobras to keep the cooler air from the hood scoop near the carb . By contrast the sheet metal heat shield underneath the intake is to keep oil away from the high temperature at the bottom of the intake heat riser crossover. The bottom of the intake becomes so hot (not cool)from the heat riser crossover that the oil can break down and burn leaving a coke deposit residue.
Bob Gaines,Shelby Enthusiast, Shelby Collector , Shelby Concours judge SAAC,MCA,Mid America Shelby

roddster

#11
Have you checked at Mansfield Mustang parts?

Royce Peterson

When we used to stuff the ports with aluminum foil the foil would get coated in a sooty carbon like goo. It eventually plugged the port pretty well. The foil never went away, it just became gooey.
1968 Cougar XR-7 GT-E 427 Side Oiler C6 3.50 Detroit Locker
1968 1/2 Cougar XR-7 428CJ Ram Air C6 3.91 Traction Lock

68stangcjfb

#13
Quote from: Bob Gaines on May 10, 2024, 10:13:50 PM
Quote from: J_Speegle on May 10, 2024, 10:05:12 PMThey make cross over block off plates for SBs never seen  or at least recall seeing them for sale for BB of any kind. Might be a small market for someone that wanted to get crafty at home in the garage,  With a couple of patterns I would start with a chunk of hard wood, trace the pattern and relief out with a bur head or drimmel tool then shape some plates and hammer them for a depression to hold them in place. SB ones are fairly thin metal so that they don't get in the way of the posts sealing (too thick of sheet metal)

Just a thought about a possibility
Thanks for the input. I am leaning towards a .030 piece of stainless in the gasket cut out for the heat riser port just enough oversize to keep from falling in and silicone the plate in with the gasket . At least until I hear a better procedure.

That's pretty much exactly what I did with mine. I used Permatex Ultra copper gasket sealer to hold them in place. That was back in 2012 and to this day the paint still hasn't come off the intake manifold so I assume they're working pretty well.
68 1/2 CJ Mustang GT FB auto 3.91s 68 1/2 CJ Torino GT FB 3.91s 60 Thunderbird 64 Falcon Sprint conv. 4Spd 65 Falcon Sedan Delivery 67 Fairlane 500 SW 428 4Spd, 68 Torino 4dr 95 Thunderbird SC. 89 F250 Supercab 2wd, 98 Mustang conv. 99 Jeep Cherokee 2002 Thunderbird. 96 Harley FLSTN Heritage Special