Hello from San Diego,
Anyone here on this site have "extra parts" for this specific transmission? I am interested in some of them and I am interested in talking to whomever about what you have! So, if you have been sitting on some of these parts for some time now and not making progress with the thought, or the actual action, and you have considered selling contact me directly at reyapnon@yahoo. Com
Mike
My old add
I still need a 28 spline output shaft for a Mustang T-10 . Might have some "M" gears to trade for one.
Hello,
GT350R On gears, all I need is a second gear 29 tooth, NEW only! In the original box...
Paul, I saw your ad a few weeks ago and private messaged you!
Mike
Quote from: Mike_Senar on April 15, 2021, 12:36:39 AM
Hello,
GT350R On gears, all I need is a second gear 29 tooth, NEW only! In the original box...
Paul, I saw your ad a few weeks ago and private messaged you!
Mike
Can't help with NOS sorry.
No help with NOS.
Hello,
I have gone through my gears now and realized I have several extra N.O.S. ones!! First gear (T10E-12) 36 tooth nickel gears. Will let go for $180.00 ea.
Also several third gears (T10M-11) 27 tooth nickel gears. Will let these go for $200.00 ea. also.
Remember, when building these transmissions one can not mix nickel and non nickel parts (unless it is for one race and you plan on tossing out the whole lot of them) due to one eating up the other!!!
I will trade for a N.O.S. 29 tooth second gear (T10M-31 or C3AZ-7102-G) Both part #'s supplied so you all can check your stash...
reyapnon@yahoo. Com
Mike
anybody know Where to find a T10 sebring input shaft nickel , i have an extra set of nickel gear , but with a regular input shaft and you said it can not been mix up ...?
And please how do you figure out the part you buy are realy nickel ones ?
Hello,
ALL extra gears are spoken for at this point! Chris NOS, e-mail me at reyapnon@yahoo. Com and I can send pictures so you will know.
Mike
i m sending an email, thank you.
5-5-21
Availability changed again!! One of the wanted posters did not need gears after all. So, there are a couple more re-available...
Mike
P.S. I am Still needing a T10M-31 29 tooth second gear. Need a new one!
PM sent
I have a T-10 second gear - 30 tooth - that I've literally used as a paperweight since 1992 when my transmission was purloined.
I have a T-5 now, so no use for this gear, other than as a conversation piece. Let me know if it may interest you.
Can I trouble someone to educate me on how to identify a gear's nickel content?
(http://www.saacforum.com/gallery/245-050521175102.jpeg)
(http://www.saacforum.com/gallery/245-050521175208.jpeg)
Jim,
That is not a nickel gear! And, the "M set" had a 29 tooth second gear, but no 30 tooth gears inside at all.
Mike
Thx Mike. My transmission requirements back in '92 were simpler: stop jumping out of 2nd gear upon deceleration.
This gear was procured by my driveline guy before he absconded with my tranny. (That just sounds wrong.) This is all I have left to show for my $1400.
Is the nickel gear identification method a deep, dark secret that should not be mentioned in polite company?
Not really but giving out the clue allows very unscrupulous types to easily fake one. The consequences unfortunately can be fatal to a transmission that had an incorrect gear installed.
that 30 tooth gear is a 1:76 second gear when clustered on a ford. came both nickel and steel on on j and l t-10s. chevys used them too.