Dennis a SAAC member sent me a 3259-1 recently that was *cough* a little rough.
I felt it was worthy of sharing
Afscarbs.com
AirFuelSpark on fb
Beautiful work as always Drew!
Chad
WOW!!! That's some outstanding work!! Excellent restoration!!
Magnificent work, a true craftsman
Quote from: FL SAAC on August 25, 2022, 08:16:37 PM
Magnificent work, a true craftsman
Well, more than that.
This is a "services offered" in that you may think your rotten piece of history is history... give me a chance. Maybe it won't be perfect, but we might make it usable again.
Worth a shot
Quote from: Drew Pojedinec on August 25, 2022, 06:50:44 PM
Dennis a SAAC member sent me a 3259-1 recently that was *cough* a little rough.
I felt it was worthy of sharing
Afscarbs.com
AirFuelSpark on fb
That is so true. You did an excellent job on the fire survivor carb I sent you. It may not look perfect, but works great.
Greek
Quote from: greekz on August 25, 2022, 08:47:41 PM
Quote from: Drew Pojedinec on August 25, 2022, 06:50:44 PM
Dennis a SAAC member sent me a 3259-1 recently that was *cough* a little rough.
I felt it was worthy of sharing
Afscarbs.com
AirFuelSpark on fb
That is so true. You did an excellent job on the fire survivor carb I sent you. It may not look perfect, but works great.
Greek
This is the same. I cannot fix the pock mark of corrosion, but the insides of this one were perfect. Even the gasket mating surfaces required very very little.
Quote from: Drew Pojedinec on August 25, 2022, 08:25:56 PM
Quote from: FL SAAC on August 25, 2022, 08:16:37 PM
Magnificent work, a true craftsman
Well, more than that.
This is a "services offered" in that you may think your rotten piece of history is history... give me a chance. Maybe it won't be perfect, but we might make it usable again.
Worth a shot
++! I commend your effort help save.
Amazing.
One would be very hard pressed to find anyone better!!!!! Drews attention to every fine detail whether a rebuild or concours restoration is unmatched in my opinion. Check out his AirFuelSpark page on FB. Amazing craftsmanship and KNOWLEDGE of the FORD Holley carburetor.
That is amazing! That carb's "before" photos look like it's been on the bottom of the ocean longer than the Titanic.
Great work Drew, thanks for sharing!
DP is a carburetor virtuoso.
Great work DP thanks.
Save the Carbs!
He worked magic on my 3300/3301 BC/BD carbs. Wonderful experience.
Do you sell good, American made needle and seat assemblies for Holley 4150 series carbs with LeMans bowls?
Quote from: rkm on August 27, 2022, 12:34:55 PM
Do you sell good, American made needle and seat assemblies for Holley 4150 series carbs with LeMans bowls?
I have 1,000 of them... I'll be totally honest, I have no idea where they were made. They have worked fine for me this far.
I could ask the supplier, but I really doubt they'd tell me the truth.
Best bet if you want american made is to reuse an original steel needle from a 3255. Just re lap the needle to the seat. I have a bucket of them if you wish to try that. I don't use them as frankly, most people don't understand the importance of fuel control or filtration, so the viton cause less issues.
Fantastic. I will order 6 sets on your site.
Nice work Drew. I just looked at your website and Im impressed. I will contact you in the near future concerning my 1967 GT-350s carb. Steve